Top 10 usual forklift mishaps ， forklift procedure ought to pay attention to these matters ！.

Don't undervalue the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous mishaps involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting heavy goods, the employees used their body weight as the counterweight, which almost caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which virtually triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Case 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not discover the forklift.
Situation 6: The forklift lifts the personnel illegally, the forklift vehicle driver does not put on the safety belt, the forklift lifter drops and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must pay attention to these issues ：.

Beginning.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that hinder the safety and security of driving, honk the horn first and afterwards start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge need to be risk-free prior to beginning.
3. When the forklift begins with a tons, the motorist should initially confirm that the lots is stable and trustworthy.
4. The start has to be slow-moving and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the mast must be tilted in reverse. .
2. Do not lift the fork expensive when driving. When getting in and leaving the task site or while driving, be careful that there will certainly be no obstacles overhead. When the tons is taking a trip, the fork has to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After unloading, the fork should be decreased to the regular driving setting before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be released first. High-speed doglegs are banned. High-speed sharp turns will certainly trigger the vehicle to lose side stability and topple. .
5. When the forklift is downhill, it is purely prohibited to switch off the flame and slide, and it is restricted to brake all of a sudden while driving with loads unless there are special conditions.
6. When the forklift is running, it should comply with the traffic rules in the factory and must maintain a particular safety and security range from the automobile ahead. .
7. When the forklift is running, the lots must be in the lowest position that does not hinder the driving, and the gantry ought to be effectively slanted back. The tons will not be increased other than when stacking or packing. .
8. The height of the load should not obstruct the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when turning around.
9. It is forbidden to switch on the ramp, nor to drive throughout the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it should drive securely at a reduced rate when going into the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for workers to base on the fork to hold items and play a stabilizing function. .
12. If problems are discovered, they will be repaired and reported in a timely manner, and they will certainly never run with ailments or hide them.

filling and dumping.
1. When fork-loading products, the range in between both forks need to be changed as needed to make the load of both forks balanced and not skewed, and one side of the product ought to be against the rack. .
2. It is prohibited to deal with a solitary fork or utilize a fork top or draw. In unique circumstances, Electric Forklift Truck for Warehouse safety and security indication should be set up to remind bordering pedestrians. .
3. In the process of packing and unloading items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle should be slow and constant. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it needs to be noted that the fork pointer need to not touch other items or things. The tons needs to be supported with marginal back tilt Electric Forklift Truck for Warehouse of the gantry to ensure that the lots does not slide in reverse. The pole can be slanted forward slightly when the lots is reduced to allow for simple placement of the lots and removal of the forks. .
6. It is forbidden to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is working, it is restricted for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to make use of forks to raise personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the hand brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the stress and temperature level are regular.
5. After the forklift is running, the external leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Single fork operation is not enabled.
2. It is not permitted to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844